Semi-matt wall paint IGIS 20
- Hiding power class 1
- Wet scrub resistance class 1
- Resistant to disinfecting agents
- Good adhesion to the surface
- Forms a vapor permeable layer
- Environment and health friendly
For interior walls and ceilings made of mineral construction materials (plaster, plasterboard, filled surfaces, wallpaper, brick masonry, concrete, etc.).
Excellent for walls and ceilings in intensively operated residential and public premises that requires frequent cleaning – corridors, stairwells, kitchens, schools, medical, food companies, etc.
6-7 m²/l, applied in 2 layers. The exact coverage rate is determined by covering the test area.
Purpose: for interior use
Binder: pure acrylic dispersion
Color: white or tinted by color cards
Density: 1,26-1,28 g/cm³
Volatile organic compounds (VOC): <30 g/l EN ISO 11890-2
Formaldehyde concentration in the tare: VdL-RL 03: 12 ppm or (12×10-4) %
Non-volatile-matter content by volume: ~37,0 %
Classification by maximum grain size: fine (to 100 μm) EN 13300
Degree of gloss, 60⁰/85⁰: <60/≥10 (semi matt) EN 13300
The loss of thickness of the coat (after 200 scrubs): <5 µm EN ISO 11998; Class 1 for wet-scrub resistance according to EN 13300
Hiding power: hiding power class 1, with a spreading rate of 6 m²/l EN ISO 6504-3 A method
Resistance to liquids (LST EN ISO 2812-1): after 24 hours there are no changes EN ISO 4628-1; EN ISO 4628-2
Work tools: brush, roller, paint spraying gun
Tool cleaning: with water
Application conditions: +10 °C to +25 °C and (35–80) % relative humidity. Avoid drafts and direct sunlight during painting. Failure to follow these recommendations, may form poor-quality paint film.
Coverage rate: 6-7 m²/l, applied in 2 layers
Drying time (23 °C, 50 % RH): dust does not stick after 1 hour. Repainting can be done only after the first layer is completely dry (after ~2-4 hours), depending on the surface, layer thickness, air temperature, humidity, etc.
The surface must be stable, dry and clean.
Unpainted surfaces: remove the mud, grease, salts. Prime porous and moisture-absorbing surfaces primed with IGIS AG deep primer. Level uneven surfaces and various cracks with the selected IGIS filler, sand and remove the dust.
Previously painted surfaces: remove the old peeling paint coating, wash the contaminated surface with soapy water or 3 % solution of soda, then rinse with clean water. Sand and dust off a glossy painted surface to improve adhesion. Treat the surface affected by fungi and mold with an anti-mold agent. Level uneven surfaces and various cracks with the selected IGIS filler, sand and remove the dust. Prime filled surfaces with primer before painting Taktika B.
Use IGIS GD primer paint to even out the color of surface.
Stir well before use. Apply 1-2 layers. Paint of the same batch shall be used to cover one surface. Stir them in one tare to ensure color uniformity.
Paint large areas without interruption in the same direction throughout the wall. An even, high-quality coating is obtained by abundantly soaking the roller in the paint. Make sure there is enough paint on the roller during painting.
The surface film acquires full strength and can be cleaned after 28 days. Clean dirty painted surface with clean lukewarm water and a soft cloth or sponge. Hot water can soften the paint film. We recommend to clean with a mild alkaline cleaners (pH 6-8). Cleaners containing organic solvents are not suitable. Do not use abrasive cleaners such as rough sponges or brushes.
Precautionary statements: keep out of reach of children, avoid release to the environment, wear protective gloves/ protective clothing/eye protective/face protective. IF ON SKIN: wash with plenty of soap and water. IF IN EYES: rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Additional hazard information: EUH208 – contains a mixture of 5-chlor-2-metil-2H-izotiazol-3-one and 2-metil-2H-izotiazol -3-one (3:1), 1,2-benzisothiazol-3(2H)-one can cause allergy in humans.
Shelf life in tightly closed original packaging: 24 months from the date of manufacture
Storage and transportation conditions: store the product tightly closed in dry well-ventilated place at a temperature of +5 ⁰C to +30 ⁰C, protect against from damage, frost and direct sunlight.
Do not pour into drains, water or soil. Empty, dry product package should be recycled or disposed of in accordance with national law.
Packing: 1 l, 3 l, 10 l buckets